Important Pre-notes first

1. Confirm LED strip voltage: 12V / 24V DC (most common). Never plug straight into mains AC 220V!


2. Check type: single-color LED strip or RGB / RGBW addressable (WS2812B). Wiring is different.


3. Safety: Unplug power supply during all wiring work.

Part 1: Single Color LED Strip (Basic White/Warm White)

Tools you need

• LED strip


• Matching DC power supply (voltage match + enough current)


• LED strip connector / soldering iron + solder


• Wire strippers, electrical tape / heat shrink tube


• Optional: dimmer

Step 1: Check strip polarity

Step 2: Cut the LED strip (if needed)

Step 3: Attach wires / connector

1. Peel off 5–8mm silicone coating on the strip pads


2. Open the connector clip


3. Slide the strip fully into the slot (align + / – correctly)


4. Press the clip tight to lock

1. Strip small wire ends


2. Solder red wire → +, black wire → –


3. Cover joints with heat shrink tube or electrical tape (prevent short circuit)

Step 4: Connect to power supply

1. Power supply terminals: DC output + and -


2. Wire from LED strip + → power supply +


3. Wire from LED strip – → power supply –

If using a dimmer: Install dimmer between power supply and LED strip

Step 5: Test power

Part 2: RGB LED Strip (4-wire: R, G, B, +V)

Step 1: Identify pins

Step 2: Connect to RGB controller

1. LED strip +V → Controller +V


2. LED strip R → Controller R


3. LED strip G → Controller G


4. LED strip B → Controller B

Step 3: Power supply to RGB controller

Do NOT power the strip directly; always use the controller for colour control.

Part 3: Addressable RGB LED Strip (WS2812B / SK6812, 3-wire)

• DI = Data IN (input side)


• DO = Data OUT (to next strip segment)
  
  
  Wiring:

1. 5V → Power positive


2. GND → Power negative


3. DI → Data pin of controller/Arduino


4. If chaining strips: Previous strip DO → Next strip DI

Common Mistakes to Avoid

1. Wrong voltage power supply (12V strip + 24V PSU = burn LEDs)


2. Reversed positive/negative polarity


3. Bare wire short circuit


4. Cutting LED strip outside scissors mark


5. Overloading power supply (calculate total LED wattage)


6. Long strip runs: Voltage drop → use power injection for long runs

Quick Wattage Calculation Tip

Step-by-Step: Single Colour LED Strip + RGB LED Strip

Pre-Work Safety Rules

• Always disconnect power when wiring.


• Match voltage: 12V or 24V DC (never mains AC directly).


• Check markings on strip pads before connecting.


• Prepare tools: wires, strippers, connectors / solder, heat shrink/tape, matching DC power supply.

1. Single Colour LED Strip (2 wires: + / −)

Wire labels on strip

Step 1 Cut the strip (if needed)

Step 2 Attach wires / clip connector

1. Peel silicone covering off copper pads.


2. Lift the plastic clip.


3. Slide strip in fully, align + and − correctly.


4. Push clip down to lock.

• Red wire = Positive (+)


• Black wire = Negative (−)
  
  
  Cover solder joints with heat shrink or tape to prevent short circuits.

Step 3 Connect to power supply

If you want brightness control:

Power supply → Dimmer → LED strip

Step 4 Test

2. RGB LED Strip (4 wires: Common Positive type – most common)

Important: This is common positive (common anode). Not common negative.

Step 1 Attach wires to LED strip

Step 2 Wire to RGB IR/RF Controller

1. Strip +V ➜ Controller +V


2. Strip R ➜ Controller R


3. Strip G ➜ Controller G


4. Strip B ➜ Controller B

Step 3 Power the RGB Controller

Step 4 Test

Simple Wiring Diagrams

Single Colour Setup

RGB Setup

Common Mistakes

1. Swapped + and − no light (will not instantly break most strips, but fix quickly)


2. Wrong voltage power supply burns LEDs


3. Bare wires touching = short circuit


4. Mixing RGB wire order wrong colours (e.g. press red, light shows green)


5. Very long strips: voltage drop (dim ends) add extra power injection